I have a 24 Port poe switch where when i plug it in few of the ports lights stay lit and nothing else. I can connect to it with a console cable i had the poe daughter board off can some one tell me if any thing is off other than missing poe hardware. also it is in a boot loop.

​

U-Boot usw-v1.1.4.115-g14af1ee6 (Feb 14 2017 - 18:50:54)

DEV ID= 0000db56
SKU ID = 0x8344
DDR type: DDR3
MEMC 0 DDR speed = 667MHz
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DDR Tune Completed
DRAM:  256 MiB
WARNING: Caches not enabled

 soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x4
PCIe port 0 in RC mode

 pos is 172
==>PCIE: LINKSTA reg 0xbe val 0x1001

**************
 port 0 is not active!!
**************
In:    serial
Out:   serial
Err:   serial
Unlocking L2 Cache ...Done
arm_clk=400MHz, axi_clk=200MHz, apb_clk=50MHz, arm_periph_clk=200MHz
Disabling outer cache
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
ubnt_bootsel_init: bootsel magic=a34de82b, bootsel = 1
UBNT application initialized
Boot partition selected = 1
Loading Kernel Image @ 1000000, size = 15728640
Verifying 'kernel1' parition:OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Ubiquiti 4.0.42.10433
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    15117632 Bytes = 14.4 MiB
   Load Address: 00018000
   Entry Point:  00018000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
boot_prep_linux commandline: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x68000000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=1

Starting kernel ...

Disabling outer cache
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.6.5 (builder@owrt1505-us48p) (gcc version 4.7.2 (OpenWrt GCC 4.7.2 unknown) ) #2 SMP Sat May 18 09:34:17 MDT 2019
[    0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Broadcom iProc
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] BUG: mapping for 0x18000000 at 0xf0000000 out of vmalloc space
[    0.000000] BUG: mapping for 0x19000000 at 0xf1000000 out of vmalloc space
[    0.000000] PERCPU: Embedded 7 pages/cpu @c1cbb000 s6272 r8192 d14208 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 61952
[    0.000000] Kernel command line: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x68000000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=1 ubootver=usw-v1.1.4.115-g14af1ee6
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB 128MB = 256MB total
[    0.000000] Memory: 244944k/244944k available, 17200k reserved, 131072K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0018000 - 0xc034d7f0   (3286 kB)
[    0.000000]       .init : 0xc034e000 - 0xc0e58880   (11307 kB)
[    0.000000]       .data : 0xc0e5a000 - 0xc0e82d40   ( 164 kB)
[    0.000000]        .bss : 0xc0e82d64 - 0xc0eb1354   ( 186 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:292
[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[    0.010000] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    0.050000] pid_max: default: 4096 minimum: 301
[    0.050000] Mount-cache hash table entries: 512
[    0.050000] CPU: Testing write buffer coherency: ok
[    0.050000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.050000] Setting up static identity map for 0x282250 - 0x2822a8
[    0.050000] L310 cache controller enabled
[    0.050000] l2x0: 8 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x0a120000, Cache size: 131072 B
[    0.050000] Brought up 1 CPUs
[    0.050000] SMP: Total of 1 processors activated (795.44 BogoMIPS).
[    0.050000] devtmpfs: initialized
[    0.060000] NET: Registered protocol family 16
[    0.060000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.060000] GENPLL[5] mdiv=40 rate=2000000000
[    0.060000] Sel=1 Ovr=1 Div=48
[    0.060000] UART clock rate 50000000
[    0.080000] bio: create slab <bio-0> at 0
[    0.080000] Bluetooth: Core ver 2.16
[    0.080000] NET: Registered protocol family 31
[    0.080000] Bluetooth: HCI device and connection manager initialized
[    0.080000] Bluetooth: HCI socket layer initialized
[    0.080000] Bluetooth: L2CAP socket layer initialized
[    0.080000] Bluetooth: SCO socket layer initialized
[    0.080000] Switching to clocksource iproc_gtimer
[    0.090000] NET: Registered protocol family 2
[    0.090000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.090000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.090000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.090000] TCP: reno registered
[    0.090000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.090000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.090000] NET: Registered protocol family 1
[   14.540000] pm_init: Initializing Power Management ....
[   14.540000] iproc gpiochip add GPIOA
[   14.540000] GPIOA:ioaddr f0000060
[   14.540000] GPIOA:intr_ioaddr f0000000 dmu_ioaddr   (null)
[   14.790000] PCIE0: LINKSTA reg 0xbe val 0x1001
[   14.790000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x1001, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x2, PCIE0 link=0
[   15.140000] PCIe port 1 in End-Point mode - ignored
[   15.140000] Registering iproc_pmu_device
[   15.140000] bounce pool size: 64 pages
[   15.160000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   15.160000] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[   15.160000] msgmni has been set to 222
[   15.160000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[   15.160000] io scheduler noop registered
[   15.160000] io scheduler deadline registered (default)
[   15.160000] io scheduler cfq registered
[   15.160000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[   15.160000] serial8250.0: ttyS0 at MMIO 0x18000400 (irq = 123) is a 16550A
[   15.640000] console [ttyS0] enabled
[   15.650000] serial8250.0: ttyS1 at MMIO 0x18000300 (irq = 123) is a 16550A
[   15.670000] brd: module loaded
[   15.690000] loop: module loaded
[   15.690000] nbd: registered device at major 43
[   15.720000] tun: Universal TUN/TAP device driver, 1.6
[   15.720000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[   15.730000] Bluetooth: HCI UART driver ver 2.2
[   15.730000] Bluetooth: HCI H4 protocol initialized
[   15.740000] Bluetooth: HCI BCSP protocol initialized
[   15.750000] TCP: cubic registered
[   15.750000] NET: Registered protocol family 10
[   15.760000] sit: IPv6 over IPv4 tunneling driver
[   15.770000] NET: Registered protocol family 17
[   15.770000] Bluetooth: RFCOMM TTY layer initialized
[   15.780000] Bluetooth: RFCOMM socket layer initialized
[   15.780000] Bluetooth: RFCOMM ver 1.11
[   15.780000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.790000] Bluetooth: BNEP filters: protocol multicast
[   15.790000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   15.800000] 8021q: 802.1Q VLAN Support v1.8
[   15.810000] GENPLL[5] mdiv=40 rate=2000000000
[   15.810000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address
[   15.820000] m25p80 spi1.0: found mx25l25635e, expected m25p80
[   15.820000] m25p80 spi1.0: mx25l25635e (32768 Kbytes)
[   15.830000] 7 cmdlinepart partitions found on MTD device spi1.0
[   15.830000] Creating 7 MTD partitions on "spi1.0":
[   15.840000] 0x000000000000-0x0000000c0000 : "u-boot"
[   15.850000] 0x0000000c0000-0x0000000d0000 : "u-boot-env"
[   15.850000] 0x0000000d0000-0x0000000e0000 : "shmoo"
[   15.860000] 0x0000000e0000-0x000000fe0000 : "kernel0"
[   15.870000] 0x000000fe0000-0x000001ef0000 : "kernel1"
[   15.880000] 0x000001ef0000-0x000001ff0000 : "cfg"
[   15.880000] 0x000001ff0000-0x000002000000 : "EEPROM"
[   15.910000] Freeing init memory: 11304K
[   15.950000] ubnt_common: module license 'Proprietary' taints kernel.
[   15.960000] Disabling lock debugging due to kernel taint
[   16.050000] gpiodev: reset_timeout=3
...running /sbin/init
init started: BusyBox v1.23.2 (2019-05-18 09:25:49 MDT)
  exec
Restoring EEPROM data from ubnthal
MAC: f0:9f:c2:09:e4:9c
Validating the active image /dev/mtd4..."4.0.42.10433"
Validating the backup image /dev/mtd3..."4.0.21.9965"
DMA pool size: 4194304
AXI unit 0: Dev 0x8344, Rev 0x01, Chip BCM53344_A0, Driver BCM56150_A0
SOC unit 0 attached to PCI device BCM53344_A0


<10> Jan  1 00:00:41 UBNT UBNT_POE[Cnfgr_Thread ]: ubnt_poe_common.c(5129) 28 %% PSE init failed 0x003f, retry 1

<10> Jan  1 00:00:44 UBNT UBNT_POE[Cnfgr_Thread ]: ubnt_poe_common.c(5129) 81 %% PSE init failed 0x003f, retry 2

<10> Jan  1 00:00:47 UBNT UBNT_POE[Cnfgr_Thread ]: ubnt_poe_common.c(5129) 82 %% PSE init failed 0x003f, retry 3

<10> Jan  1 00:00:47 UBNT UBNT_POE[Cnfgr_Thread ]: ubnt_poe_common.c(3974) 83 %% PoE Initialization failed in Hardware

cnfgrApiCallback: Failed by component 171 - UBNT_POE
task 0x339baf4 - Cnfgr_Thread
Cnfgr current state 150 - UNKNOWN
Cnfgr next state 150 - UNKNOWN
The system is restarting due to the inconsistent state 171 in file: cnfgr_tally.c line 233

<8> Jan  1 00:00:48 UBNT LOG[Cnfgr_Thread ]: log_cnfgr.c(1258) 85 %% The system is restarting due to inconsistent state.

Switching software SIGSEGV Handler
This build was configured to copy this crash information to
  a file.
Symbols already loaded.
/home/builder/uap.work/build/openwrt/build_dir/arm/fastpath/src/mgmt/broadcom/cli_web_mgr/cli_web_util.c: 1395: Failed to create cliWebIORedirectHandle

<9> Jan  1 00:00:59 UBNT SIM[SimAddrConflict]: sim.c(4669) 198 %% Failed to read conflicting ARP packet from stack - errno Resource temporarily unavailable

Please press Enter to activate this console.

UBNT login: ubnt
Password:


BusyBox v1.23.2 (2019-05-18 09:25:49 MDT) built-in shell (ash)


  ___ ___      .__________.__
 |   |   |____ |__\_  ____/__|
 |   |   /    \|  ||  __) |  |   (c) 2010-2019
 |   |  |   |  \  ||  \   |  |   Ubiquiti Networks, Inc.
 |______|___|  /__||__/   |__|
            |_/                  https://www.ui.com/

      Welcome to UniFi USW-24P-250!

UBNT-US.v4.0.42#   exec
umount: can't remount rootfs read-only
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to[   76.540000] Disabling non-boot CPUs ...
[   76.540000] Restarting system.


U-Boot usw-v1.1.4.115-g14af1ee6 (Feb 14 2017 - 18:50:54)

DEV ID= 0000db56
SKU ID = 0x8344
DDR type: DDR3
MEMC 0 DDR speed = 667MHz
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DDR Tune Completed
DRAM:  256 MiB
WARNING: Caches not enabled

 soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1
PCIe port 0 in RC mode

 pos is 172
==>PCIE: LINKSTA reg 0xbe val 0x1001

**************
 port 0 is not active!!
**************
In:    serial
Out:   serial
Err:   serial
Unlocking L2 Cache ...Done
arm_clk=400MHz, axi_clk=200MHz, apb_clk=50MHz, arm_periph_clk=200MHz
Disabling outer cache
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
ubnt_bootsel_init: bootsel magic=a34de82b, bootsel = 1
UBNT application initialized
Boot partition selected = 1
Loading Kernel Image @ 1000000, size = 15728640
Verifying 'kernel1' parition:OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Ubiquiti 4.0.42.10433
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    15117632 Bytes = 14.4 MiB
   Load Address: 00018000
   Entry Point:  00018000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
boot_prep_linux commandline: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x680            00000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0)            ,15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=1

Starting kernel ...

Disabling outer cache